Top 20 Best 3950 Thermistors

 

Dovewill NTC 100K Ohm 3950 Thermistor Temperature Sensor Accessories For 3D Printer

Dovewill NTC 100K Ohm 3950 Thermistor Temperature Sensor Accessories For 3D Printer

Dovewill NTC 100K Ohm 3950 Thermistor Temperature Sensor Accessories For 3D Printer - To avoid the direct or indirect rain and snow and mechanical damage. Products should be stored in the environment at a temperature of 10 ℃ / +40 ℃, relative humidity of not more than 80%, the surrounding environment should not have acidic, alkaline substances and corrosive gases or radiation sources. When measuring the temperature, if the measured temperature does not match the temperature of the computer, check whether the thermistor is installed in the correct position or check whether there is temperature interference in the surrounding environment., Rapid response structure., High sensitivity. Description, this is pre-wired thermistor for reprap 3d printer extruder or heated bed., High quality, stable performance., Easy to install. The two pins do not force the root pull, so as not to damage the pin. Specification, length1040mm, high temperature teflon wire temperature 200 degrees, nominal resistance r25 (25 ℃) 100k, resistance accuracy ± 1%, b value r25 / 50 3950k, b value accuracy ± 1%, operating temperature range -40 ℃ ~ +300 ℃, dissipation power factor ≥ 5 mw / ℃ (static air), thermal time constant ≤ 7s (static air), maximum rated power 45mwpackage includes1x temperature sensornoteas the thermistor is sealed, please do not violent vibration or squeeze, so as not to break the glass tube.

 

ShineBear 10PCS Reprap 3950 Thermistor 100K  1 Meter wire for Printer Bed Hot End

ShineBear 10PCS Reprap 3950 Thermistor 100K + 1 Meter wire for Printer Bed Hot End

ShineBear 10PCS Reprap 3950 Thermistor 100K + 1 Meter wire for Printer Bed Hot End - High accuracy 1%. Throat installed ptfe lined barrel, trouble free print.  ntc3950 thermistor. Mk8 makerbot nozzle 04mm. 12v 40w cartridge heater.

 

Aibecy DIY Volcano J-head Hotend Hot End Kit for 175mm Filament 04mm Nozzle 12V 40W Heater 100K NTC 3950 Thermistor Heater Block for RapRep i3 3D Printer Replacement

Aibecy DIY Volcano J-head Hotend Hot End Kit for 1.75mm Filament 0.4mm Nozzle & 12V 40W Heater & 100K NTC 3950 Thermistor & Heater Block for RapRep i3 3D Printer Replacement

Aibecy DIY Volcano J-head Hotend Hot End Kit for 1.75mm Filament 0.4mm Nozzle & 12V 40W Heater & 100K NTC 3950 Thermistor & Heater Block for RapRep i3 3D Printer Replacement - 4mm heater 12v 40w thermistor 100k ntc 3950 item weight 45g / 1. 4mm output nozzle. With heater block. 75mm filament.  Specifications filament diameter 1. Pre-wired ntc3950 thermistor, 100k ohm. 6ozpacking list 1 set of hot endnote please check the size and the electric parameter of the parts carefully before you place an order. Features j-head hotend kit for damaged 3d printer hot end, suits for 1. 12v 40w heater. 75mm nozzle 0.  .

 

1Pcs 100K Ohm Ntc 3950 Thermistors With Dupont Head For 3D Printer Mend

1Pcs 100K Ohm Ntc 3950 Thermistors With Dupont Head For 3D Printer Mend

1Pcs 100K Ohm Ntc 3950 Thermistors With Dupont Head For 3D Printer Mend - Wide temperature range -40 degree ~ +300 degree, good stability, high reliability. Can provide different r, b value of the product, interchangeability, high precision. Length1m. Head size 5 255mm. Compact structure, easy installation, good waterproof.

 

BIQU 100K ohm NTC 3950 Thermistor with 1 Meter Cable for 3D Printer RepRap Mend HeatbedPack of 5pcs

BIQU 100K ohm NTC 3950 Thermistor with 1 Meter Cable for 3D Printer RepRap Mend Heatbed(Pack of 5pcs)

BIQU 100K ohm NTC 3950 Thermistor with 1 Meter Cable for 3D Printer RepRap Mend Heatbed(Pack of 5pcs) - Small size 125mmx20mm glass bead. Resistance value at 25°c=100k. Temperature sensor 100kΩ accuracy of ± 1%. Conveniently pre-wired with 1 meter long high temperature ptfe insulated wiring. Wiring insulation high temperature teflon/ptfe.

 

KKmoon DIY Hot End Kit 04mm Nozzle M6 30mm Extruder Throat 12V 40W Heater NTC 3950 Thermistor Aluminum Heater Block for 3D Printer

KKmoon DIY Hot End Kit 0.4mm Nozzle & M6 30mm Extruder Throat & 12V 40W Heater & NTC 3950 Thermistor & Aluminum Heater Block for 3D Printer

KKmoon DIY Hot End Kit 0.4mm Nozzle & M6 30mm Extruder Throat & 12V 40W Heater & NTC 3950 Thermistor & Aluminum Heater Block for 3D Printer - 12v 40w 620mm cartridge heater. Diy replacement kit universal for damaged anet a2 & a3-s a6 & a8 3d printer 3d printer hot end, special for printer. 04mm output nozzle, aluminum heater block. Pre-wired ntc3950 thermistor, 100k ohm, 11m in length. 6mm diameter external thread extruder throat, 30mm length, suits for 175mm filament.

 

Generic 100K ohm NTC 3950 Thermistors with cable for 3D Printer Reprap Mend

Generic 100K ohm NTC 3950 Thermistors with cable for 3D Printer Reprap Mend

Generic 100K ohm NTC 3950 Thermistors with cable for 3D Printer Reprap Mend - 100% brand new and high quality100k ntc b 3950 thermistors with 1m wire cable for 3d printer reprap mend 200 c 300vparameter100k����1%b 3950length1mcable diameter105mmcable temperature > 200 degrees 300v.

 

RepRap Champion 3 PCS NTC3950 Thermistors for RepRap 3D Printer Extruder or Heated Bed pre-wired with Teflon Insulated Wiring

RepRap Champion 3 PCS NTC3950 Thermistors for RepRap 3D Printer Extruder or Heated Bed pre-wired with Teflon Insulated Wiring

RepRap Champion 3 PCS NTC3950 Thermistors for RepRap 3D Printer Extruder or Heated Bed pre-wired with Teflon Insulated Wiring - Ntc 3950 thermistor features, for 3d printers use temp_sensor 11 in marlin firmware, small size 1. 0mm glass bead, high accuracy 1%, resistance value at 25°c=100k, wiring insulation high temperature teflon/ptfe, wiring length 1 meter package contents, 3 x ntc 3950 100k thermistor assembled with 1 meter teflon wiring. Thermistors have been pre-wired for your convenience with 1 meter teflon insulated wires. 25mmx2. Lot of 3 pcs ntc 3950 thermistors.

 

RepRap Champion Metal DIY Hot End for RepRap 3D Printer 175mm Filament 04mm Nozzle 12V 40W Heater NTC 3950 Thermistor Hotend

RepRap Champion Metal DIY Hot End for RepRap 3D Printer 1.75mm Filament, 0.4mm Nozzle, 12V 40W Heater, NTC 3950 Thermistor Hotend

RepRap Champion Metal DIY Hot End for RepRap 3D Printer 1.75mm Filament, 0.4mm Nozzle, 12V 40W Heater, NTC 3950 Thermistor Hotend - Low profile design, height is only 39mmm. Pre-wired ntc3950 thermistor. Stainless ptfe lined barrel for trouble free, low friction print. Plenty of mk8 clone nozzles compatible with this hotend, nozzle replacement is cheap and easy. Use it with heatsink or cooled metal base.

 

BIQU 3D Volcano hot end eruption pack kit Hotend Volcano Extra Nozzles  Volcano Extra Heater BlockNTC 3950 Thermistor for 3D Printer 17530mm ABS PLA Filament

BIQU 3D Volcano hot end eruption pack kit Hotend Volcano Extra Nozzles + Volcano Extra Heater Block+NTC 3950 Thermistor for 3D Printer 1.75/3.0mm ABS PLA Filament

BIQU 3D Volcano hot end eruption pack kit Hotend Volcano Extra Nozzles + Volcano Extra Heater Block+NTC 3950 Thermistor for 3D Printer 1.75/3.0mm ABS PLA Filament - Works with 175mm/3mm 3d printer filament. Hight print speed pack for large print size 3d printer. Heater ceramic cartridge and thermistor are included. 12v 40w heater ceramic cartridge with 100k ntc 3950 thermistor. 175mm-04+06+08+10+12mm nozzle,30mm-04+06+08+10+12mm nozzle, full range of nozzle sizes for your volcano.

 

Metal DIY Hot End for RepRap 3D Printer 175mm Filament 04mm Nozzle 12V 40W Heater NTC 3950 Thermistor Hotend

Metal DIY Hot End for RepRap 3D Printer 1.75mm Filament, 0.4mm Nozzle, 12V 40W Heater, NTC 3950 Thermistor Hotend

Metal DIY Hot End for RepRap 3D Printer 1.75mm Filament, 0.4mm Nozzle, 12V 40W Heater, NTC 3950 Thermistor Hotend - Plenty of mk8 clone nozzles compatible with this hotend, nozzle replacement is cheap and easy. Pre-wired ntc3950 thermistor. Clamping screw and washer for easy thermistor mounting. Use it with heatsink or cooled metal base. Stainless ptfe lined barrel for trouble free, low friction print.

 

MK2A 300x200mm Aluminum Heated Bed Hot Bed for RepRap 3D Printer 12V  Wiring  NTC 3950 Thermistor - Upgrade you Prusa i3 for LARGE Printsize

MK2A 300x200mm Aluminum Heated Bed Hot Bed for RepRap 3D Printer 12V + Wiring + NTC 3950 Thermistor – Upgrade you Prusa i3 for LARGE Printsize

MK2A 300x200mm Aluminum Heated Bed Hot Bed for RepRap 3D Printer 12V + Wiring + NTC 3950 Thermistor – Upgrade you Prusa i3 for LARGE Printsize - Upgrade your prusa i3 for 1 1/2 times larger print size and volume. Please see supplied drawing for dimensions and mounting hole pattern. Specifications dimensions 314mm x 214mm mounting hole diameter 3. 2mm material aluminum 3mm thick voltage 12v resistance 1. You can print directly on it, or you can put borosilicate glass on top. This heated bed made of 3 mm aluminum and it works as heat producer, heat spreader and print surface. 3 ohm package contents 1 x mk2a 300x200mm aluminum heated bed 1 x ntc 3950 pre-wired thermistor, wiring is 1 meter long 2 x power wires, 1 meter long each.

 

NTC 3950 Thermistor Temperature Sensor 10K OHM 1 Waterproof Probe for ArduinoUSA Fast Ship

NTC 3950 Thermistor Temperature Sensor 10K OHM 1% Waterproof Probe for Arduino(USA Fast Ship)

NTC 3950 Thermistor Temperature Sensor 10K OHM 1% Waterproof Probe for Arduino(USA Fast Ship) - Stainless steel probe cover is 49mm diameter 20mm long. 2 wire clip connector, range of -20, +105 celcius. As guaranteed by the shipping policy and from our experience, the items should reach the customer in 10 working days (2 weeks) or less. Acts as a variable resistor the value of the resistance changes with temperatur. Rated accuracy of within 1%.

 

TOOTO 3 PCS 100Kohm NTC 3950 Thermistors with Teflon Insulated Wiring for RepRap Prusa 3D Printer Extruder or Heated Bed pre-wired

TOOTO 3 PCS 100Kohm NTC 3950 Thermistors with Teflon Insulated Wiring for RepRap Prusa 3D Printer Extruder or Heated Bed pre-wired

TOOTO 3 PCS 100Kohm NTC 3950 Thermistors with Teflon Insulated Wiring for RepRap Prusa 3D Printer Extruder or Heated Bed pre-wired - Ntc 3950 thermistor features, for 3d printers use temp_sensor 11 in marlin firmware, small size 1. 0mm glass bead, high accuracy 1%, resistance value at 25¡ãc=100k, wiring insulation high temperature teflon/ptfe, wiring length 1 meter package contents, 3 x ntc 3950 100k thermistor assembled with 1 meter teflon wiring. Lot of 3 pcs ntc 3950 thermistors. 25mmx2. Thermistors have been pre-wired for your convenience with 1 meter teflon insulated wires.

 

3D Printer Extruder Hot Bed 100K Ohm Ntc 3950 Thermistors With Cable

3D Printer Extruder Hot Bed 100K Ohm Ntc 3950 Thermistors With Cable

3D Printer Extruder Hot Bed 100K Ohm Ntc 3950 Thermistors With Cable - 25mmx2. Thermistor temperature value table for marlin small size 1. 0mm glass bead high accuracy 1% resistance value at 25°c=100k wiring insulation high temperature teflon/ptfe wiring length 1 meter.

 

Witbot 1m 100K NTC3950 Thermistors for Reprap 3D Printer Extruder or Heated BedPack of 5pcs

Witbot 1m 100K NTC3950 Thermistors for Reprap 3D Printer Extruder or Heated Bed(Pack of 5pcs)

Witbot 1m 100K NTC3950 Thermistors for Reprap 3D Printer Extruder or Heated Bed(Pack of 5pcs) - 100k ntc3950, high accuracy. 1 meter long temperature teflon insulated wiring. Support for ntc 3950 is included in marlin firmware, use temp_sensor 11 in firmware configuration. Low cost thermistor for reprap 3d printers. Can be used with extruder or heated bed.

 

Aibecy NTC 3950 100K ohm Thermistor Sensor with 11m Cable for RepRap i3 Anet 3D Printer Kit Replacement Parts

Aibecy NTC 3950 100K ohm Thermistor Sensor with 1.1m Cable for RepRap i3 Anet 3D Printer Kit Replacement Parts

Aibecy NTC 3950 100K ohm Thermistor Sensor with 1.1m Cable for RepRap i3 Anet 3D Printer Kit Replacement Parts - 1m working temperature range -40°c~+300°c package size 7 5 1cm / 2. 3ozpackage list 1 thermistornote the item only includes the thermistor. With 1. 3p terminal for connecting. Specifications material high temperature teflon(200°c) resistance at 25°c=100k ohm cable length approx. 1m long high temperature insulated wire. 4in package weight 8g / 0. 1. Durable material for long life. Features ntc pre-wired thermistor for most 3d printers heat bed & extruder. 8 2 0. 100k ohm temperature sensor.

 

ROSENICE 5pcs NTC 3950 Thermistors for RepRap 3D Printer Extruder or Heated Bed

ROSENICE 5pcs NTC 3950 Thermistors for RepRap 3D Printer Extruder or Heated Bed

ROSENICE 5pcs NTC 3950 Thermistors for RepRap 3D Printer Extruder or Heated Bed - Popular low cost thermistor for reprap 3d printers use it with heated bed or extruder. Ntc3950 thermistors for reprap 3d printer extruder or heated bed pre-wired with teflon insulated wiring. Conviniently pre-wired with 1 meter long high temperature teflon insulated wiring. Support for ntc 3950 is included in marlin firmware, use temp_sensor 11 in firmware configuration. Color white material plastic, metal.

 

Dovewill DIY Hot End Kit 04mm Nozzle M6 30mm Extruder Throat 12V 40W Heater NTC 3950 Thermistor Aluminum Heater Block for 3D Printer

Dovewill DIY Hot End Kit 0.4mm Nozzle & M6 30mm Extruder Throat & 12V 40W Heater & NTC 3950 Thermistor & Aluminum Heater Block for 3D Printer

Dovewill DIY Hot End Kit 0.4mm Nozzle & M6 30mm Extruder Throat & 12V 40W Heater & NTC 3950 Thermistor & Aluminum Heater Block for 3D Printer - 1m, working temperature range -40℃~+300℃m6 x30mm extruder throat, material stainless steel & teflon, input diameter 1. 75mm, length 30mm, external thread diameter 6mm, threaded bore one end diameter 4mm (hole size), deep 20mm,, the other end of the hole diameter 2mm (hole size), 10mm deep, screw diameter 6mm, plus teflon tube, long 20mm, outside diameter 4mm, inner diameter 2mmnozzle, material brass, input diameter 1. 8 0., 6mm diameter external thread extruder throat, 30mm length, suits for 1. 75mm & 3mm, output diameter 0. 4mmheater, material stainless steel, voltage 12v, power 40w, wire length approx. 8 0., Pre-wired ntc3950 thermistor, 100k ohm, 1. 1m in length. 4in(lwh), suits for a2 & a8 3d printerpackage includes1xset of hot end., 0., Aluminum heater block. Description, diy replacement kit universal for damaged 3d printer hot end, special for ta2 & a8 printer. 1. 4mm output nozzle. 1mheater block, material aluminum, dimensions 2 2 1cm / 0., 12v 40w 620mm cartridge heater. 75mm filament. Specificationntc3950 thermistor, material high temperature teflon(200℃), resistance at 25°c=100k ohm, cable length approx.

 

Witbot Metal Hotend set 04mm Nozzle 12V 40W Heater NTC 3950 Thermistor Hotend for RepRap 3D Printer Filament 175mm

Witbot Metal Hotend set 0.4mm Nozzle 12V 40W Heater NTC 3950 Thermistor Hotend for RepRap 3D Printer Filament 1.75mm

Witbot Metal Hotend set 0.4mm Nozzle 12V 40W Heater NTC 3950 Thermistor Hotend for RepRap 3D Printer Filament 1.75mm - 4mm resistance value at 25c=100k  12v 40w cartridge heater  package list 1 x mk8 nozzle 1 x throat 1 x 12v 40w heater cartridge 1 x ntc 3950 pre-wired thermistor.  specification high accuracy 1% mk8 makerbot nozzle  diameter 0.