19 Greatest 70 Durometers

 

10mm x 1mm 1x10mm Metric Buna-N NBR O-Rings Bulk 70 Durometer Black 10mm ID 12mm OD 1mm Cross Section  50 Pack  Pieces

10mm x 1mm (1x10mm) Metric Buna-N NBR O-Rings Bulk, 70 Durometer, Black, 10mm ID, 12mm OD, 1mm Cross Section ( 50 Pack / Pieces )

10mm x 1mm (1x10mm) Metric Buna-N NBR O-Rings Bulk, 70 Durometer, Black, 10mm ID, 12mm OD, 1mm Cross Section ( 50 Pack / Pieces ) - Nitriles are usually sulfur cured, but peroxide curing is also possible, resulting in improved compression set. However, an increase in the acrylonitrile content compromises low temperature flexibility, and increases compound hardness. O-rings commonly provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. It can be used in temperatures between -30 degrees f (-34 degrees c) to 250 degrees f (121 degrees c), and is compatible for use with petroleum, hfa, hfb and hfc fluids, vegetable oil, alcohol, acids and aliphatic hydrocarbons. However, nbr will accept many anti-degradants, most notably pvc, which offer some degree of improvement of these deficiencies. O-rings are available in various sizes, and can be ordered based on required nominal inside diameter (id), outer diameter (od), and cross-sectional (cs) diameter. Nitrile should not be exposed to direct sunlight or moderate to high levels of atmospheric ozone, as rapid deterioration will result. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. Typical acn content ranges from 18% to 50%. These buna o-rings have a shore durometer (hardness of a material, and its resistance to permanent indentation) listed in the title above. Nitrile is the one of the most widely used rubber materials, due to its combination of low cost, resistance to many chemicals, and good physical properties. A higher durometer value indicates greater resistance to indentation. The acrylonitrile content of this highly polar elastomer provides excellent oil and gas permeation resistance, which increases as the level of acn increases. Note the picture shows an example of the o-rings, you will receive an item of similar design in the amount and specifications stated in the title. Buna-nitrile can have high tensile strength, and abrasion, tear, and compression set resistance.

 

Sterling Seal ORSIL214x25 Number-214 Standard Silicone O-Ring has Excellent Resistance to Oxygen Ozone and Sunlight Vinyl Methyl Silicone 70 Durometer Hardness 1 ID 1-14 OD Pack of 25

Sterling Seal ORSIL214x25 Number-214 Standard Silicone O-Ring has Excellent Resistance to Oxygen, Ozone and Sunlight, Vinyl Methyl Silicone, 70 Durometer Hardness, 1″ ID, 1-1/4″ OD (Pack of 25)

Sterling Seal ORSIL214x25 Number-214 Standard Silicone O-Ring has Excellent Resistance to Oxygen, Ozone and Sunlight, Vinyl Methyl Silicone, 70 Durometer Hardness, 1″ ID, 1-1/4″ OD (Pack of 25) - Sterling seal & supply silicone o-ring, has excellent heat and compression resistance, excellent flexibility, and good electrical insulator. At high temperatures, silicone o-rings are superior to most other elastic materials. Silicone has limitations, aromatic hydrocarbons (benzene, toluene), aromatic mineral oil, acids and alkalis, superheated water or steam over 250 f. Silicone o-ring, has good resistance to fungal and biological attack. Silicone o-ring, service temperature is -90 f to 500 f (-68 c to 260 c).

 

Buna-N O-Ring Kit 70A Durometer 382 Pieces 30 Sizes

Buna-N O-Ring Kit, 70A Durometer, 382 Pieces, 30 Sizes

Buna-N O-Ring Kit, 70A Durometer, 382 Pieces, 30 Sizes - For use across a wide temperature range from -30 degrees f/-34 degrees c to 250 degrees f/121 degrees c. Meets aerospace standard as568a for quality assurance. Made of buna-nitrile (also called buna-n) for use with a variety of fluids from petroleum to aliphatic hydrocarbons and has a durometer (hardness) of 70a for resistance to penetration. Plastic case for portability and organized storage. Includes 382 pieces for covering 30 dash sizes.

 

CleverDelights Solid Rubber Cord - 34 Diameter - 5 Feet - Buna 70 Durometer - Black - 075 Round

CleverDelights Solid Rubber Cord – 3/4″ Diameter – 5 Feet – Buna 70 Durometer – Black – 0.75″ Round

CleverDelights Solid Rubber Cord – 3/4″ Diameter – 5 Feet – Buna 70 Durometer – Black – 0.75″ Round - Buna compound is resistant to gasoline, oils, and grease — recommended temperature range of -30f to 250f. Commonly used as o-ring rubber cord stock as well as various other applications. Solid buna rubber cord — durometer (hardness) 70 — tensile strength 1450 psi. Length 5 feet — diameter 3/4″ round — color black. Cleverdelights brand — ships from a usa warehouse by a usa-based company.

 

Sterling Seal OR70CLRURE009X50 009 O-Ring Urethane 70 Durometer Hardness Pack of 50

Sterling Seal OR70CLRURE009X50 009 O-Ring, Urethane, 70 Durometer Hardness (Pack of 50)

Sterling Seal OR70CLRURE009X50 009 O-Ring, Urethane, 70 Durometer Hardness (Pack of 50) - 1-1/16id nominal x  1-3/16od nominal x  1/16cs nominal. Sterling seal & supply urethane o-rings have tensile strength of up to 6,000 psi, elongation of 350 to 650 percent, compression sets of 10 to 25 percent, and exceedingly high abrasion resistance. Common end use applications are industrial seals, industrial rolls, o-rings, caster wheels, gaskets, shoe soles and conveyor belts. Sterling seal & supply 70 durometer urethane seals are ideal for high hydraulic pressures and situations where highly stressed parts are subject to wear. Sterling seal & supply urethane o-rings are compatible with hydraulic fluids, weak acids and bases, and mixtures containing less than 80 percent aromatic constituents.

 

Sterling Seal ORSIL009x25 Number-009 Standard Silicone O-Ring Excellent Resistance to Oxygen Ozone and Sunlight Vinyl Methyl Silicone 70 Durometer Hardness 732 ID 1132 OD Pack of 25

Sterling Seal ORSIL009x25 Number-009 Standard Silicone O-Ring, Excellent Resistance to Oxygen, Ozone and Sunlight, Vinyl Methyl Silicone, 70 Durometer Hardness, 7/32″ ID, 11/32″ OD (Pack of 25)

Sterling Seal ORSIL009x25 Number-009 Standard Silicone O-Ring, Excellent Resistance to Oxygen, Ozone and Sunlight, Vinyl Methyl Silicone, 70 Durometer Hardness, 7/32″ ID, 11/32″ OD (Pack of 25) - Silicone o-ring, service temperature is -90 f to 500 f (-68 c to 260 c). Silicone has limitations, aromatic hydrocarbons (benzene, toluene), aromatic mineral oil, acids and alkalis, superheated water or steam over 250 f. Sterling seal & supply silicone o-ring, has excellent heat and compression resistance, excellent flexibility, and good electrical insulator. At high temperatures, silicone o-rings are superior to most other elastic materials. Silicone o-ring, has good resistance to fungal and biological attack.

 

Sur-Seal ORSIL342 Number 342 Standard Silicone O-Ring Excellent Resistance to Oxygen Ozone and Sunlight Vinyl Methyl Silicone 70 Durometer Hardness 3-58 ID 4 OD

Sur-Seal ORSIL342 Number 342 Standard Silicone O-Ring, Excellent Resistance to Oxygen, Ozone and Sunlight, Vinyl Methyl Silicone, 70 Durometer Hardness, 3-5/8″ ID, 4″ OD

Sur-Seal ORSIL342 Number 342 Standard Silicone O-Ring, Excellent Resistance to Oxygen, Ozone and Sunlight, Vinyl Methyl Silicone, 70 Durometer Hardness, 3-5/8″ ID, 4″ OD - Silicone has limitations, aromatic hydrocarbons (benzene, toluene), aromatic mineral oil, acids and alkalis, superheated water or steam over 250 f. Sterling seal & supply silicone o-ring, has excellent heat and compression resistance, excellent flexibility, and good electrical insulator. At high temperatures, silicone o-rings are superior to most other elastic materials. Silicone o-ring, service temperature is -90 f to 500 f (-68 c to 260 c). Silicone o-ring, has good resistance to fungal and biological attack.

 

Sax 70 Durometer Urethane Silkscreen Squeegee - 8 inches

Sax 70 Durometer Urethane Silkscreen Squeegee – 8 inches

Sax 70 Durometer Urethane Silkscreen Squeegee – 8 inches - High quality squeegee with 8″ neoprene blade. Designed to provide crisp images when printing on paper, cardboard and wood. For printing on paper, cardboard or wood. Neoprene blades are suited for short print runs. Blades have square edges and are securely fastened to a contoured wood handle. Square edge blade is securely fastened to the handle. Durable wooden handle is contoured for comfort. Urethane blades are firm and impervious to acids, turpentine & thinners and suited for high usage applications. Sold as single unit.

 

Sur-Seal ORVT021 Viton Number-021 Standard O-Ring Fluoropolymer Elastomer 70 Durometer Hardness 1516 ID 1-116 OD

Sur-Seal ORVT021 Viton Number-021 Standard O-Ring, Fluoropolymer Elastomer, 70 Durometer Hardness, 15/16″ ID, 1-1/16″ OD

Sur-Seal ORVT021 Viton Number-021 Standard O-Ring, Fluoropolymer Elastomer, 70 Durometer Hardness, 15/16″ ID, 1-1/16″ OD - Limitations are steam, hot water, amines, polar solvents, low molecular weight organic solvents and glycol-based brake fluids  ammonia gas, low molecular organic acids (formic and acetic acids). Excellent resistance to acids, fuels, mineral and vegetable oils and greases, aliphatic, aromatic and chlorinated hydrocarbons, non-flammable hydraulic fluids (hfd) and many organic solvents and chemicals. This compound offers excellent chemical, temperature, aging, and ozone resistance. Low swelling in astm oil no 1, and irm 902 and irm 903. Temperature range 2 degrees to 400 degrees f (-16 degrees to 204 degrees c).

 

Sterling Seal ORSIL206x10 Number-206 Standard Silicone O-Ring has Excellent Resistance to Oxygen Ozone and Sunlight Vinyl Methyl Silicone 70 Durometer Hardness 12 ID 34 OD Pack of 10

Sterling Seal ORSIL206x10 Number-206 Standard Silicone O-Ring has Excellent Resistance to Oxygen, Ozone and Sunlight, Vinyl Methyl Silicone, 70 Durometer Hardness, 1/2″ ID, 3/4″ OD (Pack of 10)

Sterling Seal ORSIL206x10 Number-206 Standard Silicone O-Ring has Excellent Resistance to Oxygen, Ozone and Sunlight, Vinyl Methyl Silicone, 70 Durometer Hardness, 1/2″ ID, 3/4″ OD (Pack of 10) - Sterling seal & supply silicone o-ring, has excellent heat and compression resistance, excellent flexibility, and good electrical insulator. Silicone o-ring, service temperature is -90 f to 500 f (-68 c to 260 c). Silicone has limitations, aromatic hydrocarbons (benzene, toluene), aromatic mineral oil, acids and alkalis, superheated water or steam over 250 f. Silicone o-ring, has good resistance to fungal and biological attack. At high temperatures, silicone o-rings are superior to most other elastic materials.

 

Sterling Seal ORBN152x10 Number-152 Standard O-Ring Buna Nitrile Rubber 70 Durometer Hardness 3-14 ID 3-716 OD Pack of 10

Sterling Seal ORBN152x10 Number-152 Standard O-Ring, Buna Nitrile Rubber, 70 Durometer Hardness, 3-1/4″ ID, 3-7/16″ OD (Pack of 10)

Sterling Seal ORBN152x10 Number-152 Standard O-Ring, Buna Nitrile Rubber, 70 Durometer Hardness, 3-1/4″ ID, 3-7/16″ OD (Pack of 10) - For use across a wide temperature range from -30 degrees f (-34 degrees c) to 250 degrees f (121 degrees c), good/excellent resistance to many petroleum oils/greases, hydraulic fluids, alcohol, mineral oil and grease. Not compatible with product fuels with a high aromatic content aromatic hydrocarbons (benzene) chlorinated hydrocarbons (trichloroethylene). Oil resistant applications of all types low temperature military uses off-road equipment automotive, marine, aircraft fuel systems 70 durometer. Buna n or nitrile has good mechanical properties when compared with other elastomers and high wear resistance 70 durometer. Compatible with aliphatic hydrocarbons (propane, butane, petroleum oil, mineral oils and greases, diesel fuel and fuel oil).

 

010 Standard Dash Size -010 Buna-N NBR O-Rings Bulk 70 Durometer Black 14 ID 38 OD 116 Cross Section  100 Pack  Pieces

010 Standard Dash Size -010 Buna-N NBR O-Rings Bulk, 70 Durometer, Black, 1/4″ ID, 3/8″ OD, 1/16″ Cross Section ( 100 Pack / Pieces )

010 Standard Dash Size -010 Buna-N NBR O-Rings Bulk, 70 Durometer, Black, 1/4″ ID, 3/8″ OD, 1/16″ Cross Section ( 100 Pack / Pieces ) - They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. However, an increase in the acrylonitrile content compromises low temperature flexibility, and increases compound hardness. Typical acn content ranges from 18% to 50%. These buna o-rings have a shore durometer (hardness of a material, and its resistance to permanent indentation) listed in the title above. However, nbr will accept many anti-degradants, most notably pvc, which offer some degree of improvement of these deficiencies. It can be used in temperatures between -30 degrees f (-34 degrees c) to 250 degrees f (121 degrees c), and is compatible for use with petroleum, hfa, hfb and hfc fluids, vegetable oil, alcohol, acids and aliphatic hydrocarbons. O-rings commonly provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. O-rings are available in various sizes, and can be ordered based on required nominal inside diameter (id), outer diameter (od), and cross-sectional (cs) diameter. Buna-nitrile can have high tensile strength, and abrasion, tear, and compression set resistance. A higher durometer value indicates greater resistance to indentation. Note the picture shows an example of the o-rings, you will receive an item of similar design in the amount and specifications stated in the title. The acrylonitrile content of this highly polar elastomer provides excellent oil and gas permeation resistance, which increases as the level of acn increases. Nitrile should not be exposed to direct sunlight or moderate to high levels of atmospheric ozone, as rapid deterioration will result. Nitriles are usually sulfur cured, but peroxide curing is also possible, resulting in improved compression set. Nitrile is the one of the most widely used rubber materials, due to its combination of low cost, resistance to many chemicals, and good physical properties.

 

Sax Silkscreen Squeegee 70 Durometer Neoprene 12 inches

Sax Silkscreen Squeegee, 70 Durometer Neoprene, 12 inches

Sax Silkscreen Squeegee, 70 Durometer Neoprene, 12 inches - Blades have square edges and are securely fastened to a contoured wood handle. Durable wooden handle is contoured for greater comfort. Designed to provide crisp images when printing on paper, cardboard and wood. Urethane blades are firm and impervious to acids, turpentine & thinners and suited for high usage applications. Neoprene blades are suited for short print runs. Sold as single unit. For printing on paper, cardboard or wood. Square edge blade is securely fastened to the handle. High quality squeegee with 12″ neoprene blade.

 

Sterling Seal ORVT202x10 Viton Number-202 Standard O-Ring Fluoropolymer Elastomer 70 Durometer Hardness 14 ID 12 OD Pack of 10

Sterling Seal ORVT202x10 Viton Number-202 Standard O-Ring, Fluoropolymer Elastomer, 70 Durometer Hardness, 1/4″ ID, 1/2″ OD (Pack of 10)

Sterling Seal ORVT202x10 Viton Number-202 Standard O-Ring, Fluoropolymer Elastomer, 70 Durometer Hardness, 1/4″ ID, 1/2″ OD (Pack of 10) - This compound offers excellent chemical, temperature, aging, and ozone resistance. Low swelling in astm oil no 1, and irm 902 and irm 903. Temperature range 2 degrees to 400 degrees f (-16 degrees to 204 degrees c). Limitations are steam, hot water, amines, polar solvents, low molecular weight organic solvents and glycol-based brake fluids  ammonia gas, low molecular organic acids (formic and acetic acids). Excellent resistance to acids, fuels, mineral and vegetable oils and greases, aliphatic, aromatic and chlorinated hydrocarbons, non-flammable hydraulic fluids (hfd) and many organic solvents and chemicals.

 

Sterling Seal ORSIL010x100 Number-010 Standard Silicone O-Ring Excellent Resistance to Oxygen Ozone and Sunlight Vinyl Methyl Silicone 70 Durometer Hardness 14 ID 38 OD Pack of 100

Sterling Seal ORSIL010x100 Number-010 Standard Silicone O-Ring, Excellent Resistance to Oxygen, Ozone and Sunlight, Vinyl Methyl Silicone, 70 Durometer Hardness, 1/4″ ID, 3/8″ OD (Pack of 100)

Sterling Seal ORSIL010x100 Number-010 Standard Silicone O-Ring, Excellent Resistance to Oxygen, Ozone and Sunlight, Vinyl Methyl Silicone, 70 Durometer Hardness, 1/4″ ID, 3/8″ OD (Pack of 100) - Silicone has limitations, aromatic hydrocarbons (benzene, toluene), aromatic mineral oil, acids and alkalis, superheated water or steam over 250 f. At high temperatures, silicone o-rings are superior to most other elastic materials. Sterling seal & supply silicone o-ring, has excellent heat and compression resistance, excellent flexibility, and good electrical insulator. Silicone o-ring, has good resistance to fungal and biological attack. Silicone o-ring, service temperature is -90 f to 500 f (-68 c to 260 c).

 

Sterling Seal ORBN151x10 Number-151 Standard O-Ring Buna Nitrile Rubber 70 Durometer Hardness 3 ID 3-316 OD Pack of 10

Sterling Seal ORBN151x10 Number-151 Standard O-Ring, Buna Nitrile Rubber, 70 Durometer Hardness, 3″ ID, 3-3/16″ OD (Pack of 10)

Sterling Seal ORBN151x10 Number-151 Standard O-Ring, Buna Nitrile Rubber, 70 Durometer Hardness, 3″ ID, 3-3/16″ OD (Pack of 10) - Oil resistant applications of all types low temperature military uses off-road equipment automotive, marine, aircraft fuel systems 70 durometer. Not compatible with product fuels with a high aromatic content aromatic hydrocarbons (benzene) chlorinated hydrocarbons (trichloroethylene). For use across a wide temperature range from -30 degrees f (-34 degrees c) to 250 degrees f (121 degrees c), good/excellent resistance to many petroleum oils/greases, hydraulic fluids, alcohol, mineral oil and grease. Buna n or nitrile has good mechanical properties when compared with other elastomers and high wear resistance 70 durometer. Compatible with aliphatic hydrocarbons (propane, butane, petroleum oil, mineral oils and greases, diesel fuel and fuel oil).

 

CleverDelights Solid Rubber Cord - 12 Diameter - 5 Feet - Buna 70 Durometer - Black - 05 Round

CleverDelights Solid Rubber Cord – 1/2″ Diameter – 5 Feet – Buna 70 Durometer – Black – 0.5″ Round

CleverDelights Solid Rubber Cord – 1/2″ Diameter – 5 Feet – Buna 70 Durometer – Black – 0.5″ Round - Commonly used as o-ring rubber cord stock as well as various other applications. Length 5 feet — diameter 1/2″ round — color black. Solid buna rubber cord — durometer (hardness) 70 — tensile strength 1450 psi. Buna compound is resistant to gasoline, oils, and grease — recommended temperature range of -30f to 250f. Cleverdelights brand — ships from a usa warehouse by a usa-based company.

 

015 Standard Dash Size -015 Buna-N NBR O-Rings Bulk 70 Durometer Black 916 ID 1116 OD 116 Cross Section  50 Pack  Pieces

015 Standard Dash Size -015 Buna-N NBR O-Rings Bulk, 70 Durometer, Black, 9/16″ ID, 11/16″ OD, 1/16″ Cross Section ( 50 Pack / Pieces )

015 Standard Dash Size -015 Buna-N NBR O-Rings Bulk, 70 Durometer, Black, 9/16″ ID, 11/16″ OD, 1/16″ Cross Section ( 50 Pack / Pieces ) - The acrylonitrile content of this highly polar elastomer provides excellent oil and gas permeation resistance, which increases as the level of acn increases. A higher durometer value indicates greater resistance to indentation. Nitriles are usually sulfur cured, but peroxide curing is also possible, resulting in improved compression set. These buna o-rings have a shore durometer (hardness of a material, and its resistance to permanent indentation) listed in the title above. Typical acn content ranges from 18% to 50%. Buna-nitrile can have high tensile strength, and abrasion, tear, and compression set resistance. It can be used in temperatures between -30 degrees f (-34 degrees c) to 250 degrees f (121 degrees c), and is compatible for use with petroleum, hfa, hfb and hfc fluids, vegetable oil, alcohol, acids and aliphatic hydrocarbons. However, an increase in the acrylonitrile content compromises low temperature flexibility, and increases compound hardness. Nitrile should not be exposed to direct sunlight or moderate to high levels of atmospheric ozone, as rapid deterioration will result. However, nbr will accept many anti-degradants, most notably pvc, which offer some degree of improvement of these deficiencies. Nitrile is the one of the most widely used rubber materials, due to its combination of low cost, resistance to many chemicals, and good physical properties. O-rings are available in various sizes, and can be ordered based on required nominal inside diameter (id), outer diameter (od), and cross-sectional (cs) diameter. Note the picture shows an example of the o-rings, you will receive an item of similar design in the amount and specifications stated in the title. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings commonly provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders.

 

Sterling Seal ORSIL114x10 Number-114 Standard Silicone O-Ring Excellent Resistance to Oxygen Ozone and Sunlight Vinyl Methyl Silicone 70 Durometer Hardness 58 ID 1316 OD Pack of 10

Sterling Seal ORSIL114x10 Number-114 Standard Silicone O-Ring, Excellent Resistance to Oxygen, Ozone and Sunlight, Vinyl Methyl Silicone, 70 Durometer Hardness, 5/8″ ID, 13/16″ OD (Pack of 10)

Sterling Seal ORSIL114x10 Number-114 Standard Silicone O-Ring, Excellent Resistance to Oxygen, Ozone and Sunlight, Vinyl Methyl Silicone, 70 Durometer Hardness, 5/8″ ID, 13/16″ OD (Pack of 10) - At high temperatures, silicone o-rings are superior to most other elastic materials. Sterling seal & supply silicone o-ring, has excellent heat and compression resistance, excellent flexibility, and good electrical insulator. Silicone has limitations, aromatic hydrocarbons (benzene, toluene), aromatic mineral oil, acids and alkalis, superheated water or steam over 250 f. Silicone o-ring, has good resistance to fungal and biological attack. Silicone o-ring, service temperature is -90 f to 500 f (-68 c to 260 c).